Assessment of the compatibility in hot melts by using different thermoanalytical methods. Ethylene/n-butyl acrylate (EBA) hot melts containing tackifiers of different nature

Por favor, use este identificador para citar o enlazar este ítem: http://hdl.handle.net/10045/69015
Información del item - Informació de l'item - Item information
Título: Assessment of the compatibility in hot melts by using different thermoanalytical methods. Ethylene/n-butyl acrylate (EBA) hot melts containing tackifiers of different nature
Autor/es: Moyano, Alejandra | París, Rodrigo | Martín-Martínez, José Miguel
Grupo/s de investigación o GITE: Adhesión y Adhesivos
Centro, Departamento o Servicio: Universidad de Alicante. Departamento de Química Inorgánica
Palabras clave: Hot melt | Copolymer of ethylene and n-butyl acrylate | Tackifier | DMA | Cloud point | Adhesion
Área/s de conocimiento: Química Inorgánica
Fecha de publicación: sep-2017
Editor: Springer Netherlands
Cita bibliográfica: Journal of Thermal Analysis and Calorimetry. 2017, 129(3): 1495-1503. doi:10.1007/s10973-017-6375-4
Resumen: Several thermoanalytical methods were used to assess the compatibility of EBA (copolymer of ethylene and n-butyl acrylate) hot melts containing tackifiers of different nature (pentaerythritol rosin ester, polyterpene resin, aliphatic hydrocarbon resin, aromatic hydrocarbon resin, and cycloaliphatic-aromatic hydrocarbon resin). The influence of the compatibility of EBA hot melts on their rheological, viscoelastic, and adhesion properties to polar (aluminum foil) and nonpolar (polypropylene film) substrates were analyzed. The viscosity and shear thinning at 160 °C of EBA hot melts varied significantly by changing the tackifier nature; however, at 180 °C all EBA hot melts showed similar viscosities and shear thinning was absent because of the rupture of physical interactions between their components. EBA copolymer showed broad tackifier compatibility, even though aliphatic and aromatic hydrocarbon resins were less compatible. Compatibility was assessed by softening point and cloud point measurement, and dynamical mechanical thermal analysis. The most compatible EBA hot melts were obtained with rosin ester, polyterpene and cycloaliphatic-aromatic hydrocarbon tackifiers and they showed the highest tack and adhesion. On the contrary, the less-compatible EBA hot melts were obtained with aromatic and aliphatic hydrocarbon tackifiers, and they showed the lowest adhesion. EBA containing aliphatic hydrocarbon tackifier was exceptional because of even being incompatible, it showed high tack.
Patrocinador/es: Financial support by REPSOL (Móstoles, Madrid, Spain) is acknowledged.
URI: http://hdl.handle.net/10045/69015
ISSN: 1388-6150 (Print) | 1588-2926 (Online)
DOI: 10.1007/s10973-017-6375-4
Idioma: eng
Tipo: info:eu-repo/semantics/article
Derechos: © Akadémiai Kiadó, Budapest, Hungary 2017
Revisión científica: si
Versión del editor: http://dx.doi.org/10.1007/s10973-017-6375-4
Aparece en las colecciones:INV - LAA - Artículos de Revistas

Archivos en este ítem:
Archivos en este ítem:
Archivo Descripción TamañoFormato 
Thumbnail2017_Moyano_etal_JThermAnalCalorim_final.pdfVersión final (acceso restringido)966,34 kBAdobe PDFAbrir    Solicitar una copia


Todos los documentos en RUA están protegidos por derechos de autor. Algunos derechos reservados.