Perylenediimide-based distributed feedback lasers with holographic relief gratings on dichromated gelatine

Empreu sempre aquest identificador per citar o enllaçar aquest ítem http://hdl.handle.net/10045/38793
Información del item - Informació de l'item - Item information
Títol: Perylenediimide-based distributed feedback lasers with holographic relief gratings on dichromated gelatine
Autors: Gutiérrez Ramírez, Manuel | Quintana Arévalo, José Antonio | Villalvilla Soria, José Moisés | Boj Giménez, Pedro | Retolaza, Aritz | Merino, Santos | Díaz-García, María A.
Grups d'investigació o GITE: Física de la Materia Condensada
Centre, Departament o Servei: Universidad de Alicante. Departamento de Física Aplicada | Universidad de Alicante. Departamento de Óptica, Farmacología y Anatomía | Universidad de Alicante. Instituto Universitario de Materiales
Paraules clau: Perylenediimide-based | Distributed feedback lasers | Holographic relief gratings | Dichromated gelatine
Àrees de coneixement: Física Aplicada | Óptica | Física de la Materia Condensada
Data de publicació: 21-de juliol-2013
Editor: American Institute of Physics
Citació bibliogràfica: Journal of Applied Physics. 2013, 114(3): 033107. doi:10.1063/1.4813873
Resum: One dimensional second-order distributed feedback (DFB) lasers consisting of polystyrene (PS) films doped with a perylenediimide laser dye, deposited over dichromated gelatine (DCG) photoresist layers with solvent resistant relief gratings recorded by holographic lithography, are reported. The advantage of using the grating on DCG in the final device is that the fabrication process is simplified and the grating pattern better preserved, since no etching methods to transfer the grating to another substrate are needed. A very simple model, proposed to explain the experimental waveguide properties, has allowed identifying the waveguide mode at which DFB emission appears, which was the key to optimize the device performance. In the frame of this model, the thickness of the PS and DCG films could be adjusted in order to minimize the laser threshold and to control its wavelength tuneability. The performance of these lasers is comparable to that of recently reported devices based on the same active material, but deposited over high-quality DFB gratings engraved on SiO2 by nanoimprint lithography.
Patrocinadors: We thank support from the Spanish Government (MINECO) and the European Community (FEDER) through Grant Nos. MAT2008-06648-C02 and MAT-2011-28167-C02, as well as to the University of Alicante. M.G.R. was supported by a CSIC fellowship within the program JAE.
URI: http://hdl.handle.net/10045/38793
ISSN: 0021-8979 (Print) | 1089-7550 (Online)
DOI: 10.1063/1.4813873
Idioma: eng
Tipus: info:eu-repo/semantics/article
Drets: Copyright © 2013 American Institute of Physics
Revisió científica: si
Versió de l'editor: http://dx.doi.org/10.1063/1.4813873
Apareix a la col·lecció: INV - Física de la Materia Condensada - Artículos de Revistas

Arxius per aquest ítem:
Arxius per aquest ítem:
Arxiu Descripció Tamany Format  
Thumbnail2013_Ramirez_etal_JAP_final.pdfVersión final (acceso restringido)997,09 kBAdobe PDFObrir     Sol·licitar una còpia
Thumbnail2013_Ramirez_etal_JAP.pdfVersión revisada (acceso abierto)408,8 kBAdobe PDFObrir Vista prèvia


Tots els documents dipositats a RUA estan protegits per drets d'autors. Alguns drets reservats.